Name |
3D Embossed WPC Decking |
Item |
3DLS146H24 |
Section |
|
Width |
146mm |
Thickness |
24mm |
Weight |
2800g/M |
Density |
1350kg/m³ |
Length |
2.4m,3.6m, or customized |
Application |
Courtyard,Garden,Park |
Surface Treatment |
Brushed and Sanding |
Warranty |
Five years |
Product Feature:
1.New technology 3D embossing WPC outdoor decoration floor, decorative enhancement. 3D embossing technology is a superficial carving technique. Each floor is the same as a sculpture, and the artistic atmosphere and visual degree have been greatly improved. Classical 3D embossing is a great improvement in seen wood-plastic floors, which cannot only be re-engraved with the bands but also support the traces of the start barking.
2.Traditional wpc composite decking are easy to lose grain on surface,super embossed decking perform better than any common composite wood,it is more natural and attractive,better fading and scratching resistant.
3.Lihua’s super embossed WPC decking have all the advantages of traditional composite decking ,it is still kept: waterproof, anti-UV, weather resistant, anti-corrosion,insect prevention, low maintenance, long service life etc…And the deep embossed boards look and feel more like the natural wood due to the 3D embossing treatment of the surface.
Data sheet |
|||
PRODUCT SPECIFICATION |
|||
Item |
Standard |
Requirements |
Result |
Slip Resistance Dry |
EN 15534-1:2014 Section6.4.2 CEN/TS 15676:2007 EN 15534-4:2014 Section 4.4 |
Pendulum value≥36 |
Longtitudinal direction:Mean 72,Min 70 Horizontal direction:Mean 79,Min 78 |
Slip Resistance Wet |
EN 15534-1:2014 Section6.4.2 CEN/TS 15676:2007 EN 15534-4:2014 Section 4.4 |
Pendulum value≥36 |
Longtitudinal direction:Mean 46,Min 44 Horizontal direction:Mean 55,Min 53 |
Falling mass impact resistance |
EN 15534-1:2014 Section7.1.2.1 EN 15534-4:2014 Section 4.5.1 |
None of the speciments shall a failure with a crack length≥ 10mm or a depth of residual indentation≥0.5mm |
Max.Crack length(mm):No crack Max.Residual indenation(mm):0.31 |
Flexural properties |
EN15534-1:2014 AnnexA EN 15534-4:2014 Section 4.5.2 |
-F’max:Mean≥3300N,Min≥3000N -Deflection under a load of 500N Mean≤2.0mm,Max≤2.5mm |
Bending Strength:27.4 MPa Modulus of elasiticity:3969 MPa Maximum load: Mean 3786N,Min 3540N Deflection at 500N: Mean:0.86mm,Max:0.99mm |
Creep behaviour |
EN 15534-1:2014 Section7.4.1 EN 15534-4:2014 Section 4.5.3 |
Known span in use: Mean ∆S≤10mm,Max ∆S≤13mm, Mean ∆Sr≤5mm |
Span: 330mm,Mean ∆S 1.65mm,Max ∆S 1.72mm,Mean ∆Sr 1.27mm |
Swelling and water absorption |
EN 15534-1:2014 Section8.3.1 EN 15534-4:2014 Section 4.5.5 |
Mean Swelling:≤4% in thickness,≤0.8% in width,≤0.4% in length Max swelling:≤5% in thickness, ≤1.2% in width,≤0.6% in length Water absorption: Mean:≤7%,Max:≤9% |
Mean Swelling:1.81% in thickness,0.22% in width,0.36% in length Max Swelling:2.36% in thickness,0.23% in width,0.44% in length Water absorption:Mean:4.32%,Max:5.06% |
Boiling Test |
EN 15534-1:2014 Section8.3.3 EN 15534-4:2014 Section 4.5.5 |
Water absorption in weight: Mean≤7%,Max≤9% |
Water absorption in weight: Mean:3.06%,Max:3.34% |
Linear thermal expansion coefficient |
EN 15534-1:2014 Section9.2 EN 15534-4:2014 Section 4.5.6 ISO 11359-2:1999 |
≤50×10⁻⁶ K⁻¹ |
34.2 x10⁻⁶ K⁻¹ |
Resistance to indentation |
EN 15534-1:2014 Section7.5 EN 15534-4:2014 Section 4.5.7 |
Brinell hardness: 79 MPa Rate of elastic recovery:65% |
|
Heat reversion |
EN 15534-1:2014 Section9.3 EN 15534-4:2014 Section 4.5.7 EN 479:2018 |
Test Temperature:100℃ Mean: 0.09% |
With proper installation and care, wood products are guaranteed to provide years of outdoor living pleasure. To achieve a trouble-free installation of wood products:
-Consult local building codes prior to installation.
-Familiarize yourself with installation instructions.
-Ensure you have all the tools and materials needed-as listed in the instruction sheet.
Storage and Handling
-Never dump wood materials when unloading.
-Store on a flat surface and cover with non-translucent material.
-When carrying wood planks, carry on edge for better support.
-Refer to installation instructions for additional guidelines on each product.
Care and Handling Guidelines For Decking
To minimize scratches, nicks, cuts and grooves, and preserve the beauty of wood decking. Follow these guidelines:
-Do not slide decks against each other when moving them. When removing them from the unit, lift the decks and set them down.
-Do not slide tools or drag equipment across the top of the decks during construction.
-Keep the surface of the decks free from construction waste.Tracking dirt and construction debris across the surface of decks, which contributes to surface scratching.
Important Information
-When working with wood products or any building materials, be sure to wear proper clothing and safety equipment.
-For all wood products, standard wood working tools may be used, as per applicable manufacturer’s instructions.
-Scrap can be discarded with normal construction debris.
-wood has excellent slip resistance wet or dry.
-wood has a built-in hidden fastener system and is easy to install wood clips.
Fastening Guidelines
-Use a minimum #8 x 2-1/2” high-quality coated, stainless steel or composite deck screw.
-Pre-drilling is required in cold weather and when within 1-1/2” of the end of the deck
-Do not use glue or caulk to fasten wood decks or to seal the joint between two decks and any other surface.This will inhibit the natural expansion and contraction of the planks and will impede the drainage of the deck.
Proper Ventilation Is Required
- To reduce moisture build-up from beneath the deck,there must be a minimum
of 12” high unobstructed continuous airspace along three sides of the deck to allow for cross ventilation.
This should be located just below the bottom of the deck joist.
-In some limited applications, including decks built against an inside corner, additional ventilation will be required where the deck meets the building. Failure to provide adequate ventilation may result in failure of the deck surface and will void the warranty.
Lisen Wood decking Installation Instructions
You can save construction time and costs by making a design, plan to budget the necessary materials according to the design intent of the programme. You can choose your own material according to your wishes with more varieties wood optional, wood construction, woodworking machinery can be used for cutting, sawing, drilling and so on.
Installation Figs of plastic clips
Install the solid decking